E1FU Cable Gland
Explosive Atmosphere Double Seal for all types of Steel & Aluminium Wire Armoured Cables

Products > E1FU Cable Gland
Explosive Atmosphere Double Seal for all types of Steel & Aluminium Wire Armoured Cables

E1FU Cable Gland
Explosive Atmosphere Double Seal for all types of Steel & Aluminium Wire Armoured Cables

INQUIRE

Globally Approved, Explosive Atmosphere Cable Gland

• Effectively earths / grounds lead sheathed cables
• Metal-to-metal armour clamping
• Direct & remote installation
• Displacement type flameproof inner seal
• Controlled outer ‘load retention’ seal
• Unique OSTG prevents overtightening
• Designed to prevent Coldflow, see CMP Technical Document TS001
• -60°C to +130°C
• Class I Zone 1, 21 and Zone 2, 22 Class I Division 2 ABCD
• Globally marked, IECEx, ATEX & cCSAus
• EMC tested

Note: † Grooved Cone (X) is predominantly used for Wire Braid (e.g. GSWB, TCWB), Steel Tape Armour (STA, DSTA) and Aluminium Strip Armour (ASA) but is also suitable for Single Wire Armour (SWA), Aluminium Wire Armour (AWA) and Pliable Wire Armour (PWA) if the range is outside that of the Stepped Cone (W).

Note: Grooved Cone (X) dimensions shown in the Cable Gland Selection Table below are for a double wire strand of braid armour cables. Tapes can also be doubled over. For cables that have only a single layer of armour such as SWA the clamping range should be used as shown in the table below.

Stepped (W) Cone is suitable for Single Wire Armour (SWA), or Aluminium Wire Armour (AWA) cables.

For under / oversized armour wires

For all types of Lead Sheathed Armoured cables

Description

E1FU Cable Gland Technical Info

 

Design SpecificationBS 6121:Part 1:1989, IEC 62444, EN 62444
Mechanical Classifications*Impact = Level 8, Retention = Class D
Enclosure ProtectionIK10 to IEC 62262 (20 joules) Brass & Stainless Steel only
Electrical Classifications *Category B (Category A when used with braid, tape or pliable wire armour cables)
ATEX CertificateSIRA13ATEX1071X, SIRA13ATEX4077X
Code of ProtectionII 2G, II 1D, Ex d IIC Gb, Ex e IIC Gb, Ex ta IIIC Da
II 3G Ex nR IIC Gc, IM2 Ex d I Mb, Ex e I Mb
Compliance StandardsEN 60079-0,1,7,15,31
IECEx CertificateIECEx SIR 13.0026X, IECEx SIM 14.0007X
Code of ProtectionEx d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da, Ex d I Mb, Ex e I Mb
Compliance StandardsIEC 60079-0,1,7,15,31
cCSAus Certificate1310517
Code of ProtectionEx d IIC; Ex e II; Ex nR II; Class I, Div 2, Groups A,B,C,D; Class II, Div 2 Groups E,F,G; Class III;
Encl Type T4X Class I, Zone 1, AEx e II / AEx nR II
Compliance StandardsCAN/CSA-C22.2 No 0,18,25,30,94,174, CAN/CSA-E60079-0,1,7, 15
ANSI/UL 514B Ed 5, ANSI/UL 50 Ed 11, ANSI/UL 2225 Ed 4, UL60079-0,1,7,15
EAC Certificate (Formerly GOST R, K & B)TC RU C-GB.AA87.B.00487
KCC Certificate14-GA4BO-0257X
NEPSI CertificateGYJ13.1140X , GYJ13.1282X
CCOE / PESO (India) CertificateP333688
INMETRO ApprovalTÜV 12.0618X
RETIE Approval03866
Marine ApprovalsLRS: 01/00172, DNV: TAE00000Y, ABS: 14-LD234401A-4-PDA, BV: 43180/A1BV
Ingress Protection Rating **IP66 as standard (IP67, IP68 available upon request)**
Deluge Protection ComplianceDTS01:91 option available on request (white ferrule for identification purposes)
Cable Gland MaterialBrass, Electroless Nickel Plated Brass, Aluminium
Seal MaterialCMP SOLO LSF Halogen Free Thermoset Elastomer
Cable TypeLead Sheathed & Single Wire Armour (LC/SWA), Lead Sheathed & Aluminium Wire Armour (LC/
AWA), Lead Sheathed & Wire Braid Armour (LC/SWB), Lead Sheathed & Pliable Wire Armour
(LC/PWA), Lead Sheathed & Steel Tape Armour (LC/STA), Lead Sheathed & Aluminium Strip
Armour (LC/ASA)
Armour ClampingReversible Armour Cone & AnyWay Universal Clamping Ring
Sealing TechniqueCMP Inner Displacement Seal & Unique CMP ‘LRS’ ™ Outer Load Retention Seal
Sealing Area(s)Cable Inner Bedding & Outer Cable Sheath
Optional AccessoriesLocknuts, Earth Tags, Serrated Washers, Entry Thread Seals, Shrouds,Ingress Discs
Optional Installation ToolsSpanners

Product Table

Metric

Cable Gland SizeAvailable Entry Threads “C” (Alternate Metric Thread Lengths Available)Lead Sheath Diameter “A”Overall
Cable
Diameter
“B”		Armour RangeAcross
Flats
“D”		Across
Corners
“D”		Protrusion
Length “F”		Combined Ordering Reference
(*Brass Metric)		ShroudCable
Gland
Weight
(Kgs)
StandardOptionGrooved
Cone (X)		Stepped Cone (W)
MetricThread Length (Metric) “E”NPTThread Length
(NPT) “E”		NPTMinMaxMinMaxMinMaxMinMaxMaxMaxSizeTypeOrdering
Suffix
20S16M2015.0½”19.9¾”3.17.86.113.10.31.00.81.2524.026.472.520S16E2FU1RAPVC040.16
20SM2015.0½”19.9¾”6.111.09.515.90.31.00.81.2524.026.470.020SE2FU1RAPVC040.15
20M2015.0½”19.9¾”6.513.412.520.90.41.00.81.2530.533.673.020E2FU1RAPVC060.21
25SM2515.0¾”20.21″11.119.314.022.00.41.21.251.637.541.389.025SE2FU1RAPVC090.33
25M2515.0¾”20.21″11.119.318.226.20.41.21.251.637.541.389.025E2FU1RAPVC090.33
32M3215.01″25.01 ¼”17.025.523.733.90.41.21.62.046.050.686.032E2FU1RAPVC110.43
40M4015.01 ¼”25.61 ½”22.031.227.940.40.41.61.62.055.060.590.040E2FU1RAPVC150.63
50SM5015.01 ½”26.12″29.537.235.246.70.41.62.02.560.066.091.050SE2FU1RAPVC180.76
50M5015.02″26.92 ½”35.642.640.453.00.61.62.02.570.177.195.050E2FU1RAPVC210.95
63SM6315.02″26.92 ½”40.148.545.659.40.61.62.02.575.082.5102.063SE2FU1RAPVC231.35
63M6315.02 ½”39.93″47.254.254.665.80.61.62.02.580.088.0104.063E2FU1RAPVC251.35
75SM7515.02 ½”39.93″52.860.259.072.00.61.62.02.590.099.0115.075SE2FU1RAPVC282.12
75M7515.03″41.53 ½”59.165.266.778.40.61.62.53.0100.0110.0117.075E2FU1RAPVC302.43
90M9024.03 ½”42.84″66.677.176.290.30.81.63.154.0114.3125.4147.090E2FU1RAPVC324.23
100M10024.03 ½”42.84″76.088.186.1101.40.81.63.154.0123.0135.3140.0100E2FU1RALSF334.47
115M11524.04″44.05″86.094.1101.5110.20.81.63.154.0133.4146.7162.0115E2FU1RALSF346.22
130M13024.05″46.8–97.0110.1110.2123.20.81.63.154.0152.4167.6174.0130E2FU1RALSF358.38
Dimensions displayed in millimeters unless otherwise stated

Imperial

Cable Gland SizeAvailable Entry Threads “C” (Alternate Metric Thread Lengths Available)Lead Sheath Diameter “A”Overall
Cable
Diameter
“B”		Armour RangeAcross
Flats
“D”		Across
Corners
“D”		Protrusion
Length “F”		Combined Ordering Reference
(*Brass Metric)		ShroudCable
Gland
Weight
(Ozs)
StandardOptionGrooved
Cone (X)		Stepped Cone (W)
MetricThread Length (Metric) “E”NPTThread Length
(NPT) “E”		NPTMinMaxMinMaxMinMaxMinMaxMaxMaxSizeTypeOrdering
Suffix
20S16M200.59½”0.78¾”0.120.310.240.520.010.040.030.050.941.042.8520S16E2FU1RAPVC045.64
20SM200.59½”0.78¾”0.240.430.370.630.010.040.030.050.941.042.7620SE2FU1RAPVC045.29
20M200.59½”0.78¾”0.260.530.490.820.020.040.030.051.201.322.8720E2FU1RAPVC067.41
25SM250.59¾”0.801″0.440.760.550.870.020.050.050.061.481.633.5025SE2FU1RAPVC0911.64
25M250.59¾”0.801″0.440.760.721.030.020.050.050.061.481.633.5025E2FU1RAPVC0911.64
32M320.591″0.981 ¼”0.671.000.931.330.020.050.060.081.811.993.3932E2FU1RAPVC1115.17
40M400.591 ¼”1.011 ½”0.871.231.101.590.020.060.060.082.172.383.5440E2FU1RAPVC1522.22
50SM500.591 ½”1.032″1.161.461.391.840.020.060.080.102.362.603.5850SE2FU1RAPVC1826.81
50M500.592″1.062 ½”1.401.681.592.090.020.060.080.102.763.043.7450E2FU1RAPVC2133.51
63SM630.592″1.062 ½”1.581.911.802.340.020.060.080.102.953.254.0263SE2FU1RAPVC2347.62
63M630.592 ½”1.573″1.862.132.152.590.020.060.080.103.153.464.0963E2FU1RAPVC2547.62
75SM750.592 ½”1.573″2.082.372.322.830.020.060.080.103.543.904.5375SE2FU1RAPVC2874.78
75M750.593″1.633 ½”2.332.572.633.090.020.060.100.123.944.334.6175E2FU1RAPVC3085.72
90M900.943 ½”1.694″2.623.043.003.560.030.060.120.164.504.945.7990E2FU1RAPVC32149.21
100M1000.943 ½”1.694″2.993.473.393.990.030.060.120.164.845.335.51100E2FU1RALSF33157.67
115M1150.944″1.735″3.393.704.004.340.030.060.120.165.255.786.38115E2FU1RALSF34219.40
130M1300.945″1.84–3.824.334.344.850.030.060.120.166.006.606.85130E2FU1RALSF35295.60
Dimensions displayed in inches unless otherwise stated

Download Spec Sheet

Download

E1FU Cable Gland Technical Info

 

Design SpecificationBS 6121:Part 1:1989, IEC 62444, EN 62444
Mechanical Classifications*Impact = Level 8, Retention = Class D
Enclosure ProtectionIK10 to IEC 62262 (20 joules) Brass & Stainless Steel only
Electrical Classifications *Category B (Category A when used with braid, tape or pliable wire armour cables)
ATEX CertificateSIRA13ATEX1071X, SIRA13ATEX4077X
Code of ProtectionII 2G, II 1D, Ex d IIC Gb, Ex e IIC Gb, Ex ta IIIC Da
II 3G Ex nR IIC Gc, IM2 Ex d I Mb, Ex e I Mb
Compliance StandardsEN 60079-0,1,7,15,31
IECEx CertificateIECEx SIR 13.0026X, IECEx SIM 14.0007X
Code of ProtectionEx d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da, Ex d I Mb, Ex e I Mb
Compliance StandardsIEC 60079-0,1,7,15,31
cCSAus Certificate1310517
Code of ProtectionEx d IIC; Ex e II; Ex nR II; Class I, Div 2, Groups A,B,C,D; Class II, Div 2 Groups E,F,G; Class III;
Encl Type T4X Class I, Zone 1, AEx e II / AEx nR II
Compliance StandardsCAN/CSA-C22.2 No 0,18,25,30,94,174, CAN/CSA-E60079-0,1,7, 15
ANSI/UL 514B Ed 5, ANSI/UL 50 Ed 11, ANSI/UL 2225 Ed 4, UL60079-0,1,7,15
EAC Certificate (Formerly GOST R, K & B)TC RU C-GB.AA87.B.00487
KCC Certificate14-GA4BO-0257X
NEPSI CertificateGYJ13.1140X , GYJ13.1282X
CCOE / PESO (India) CertificateP333688
INMETRO ApprovalTÜV 12.0618X
RETIE Approval03866
Marine ApprovalsLRS: 01/00172, DNV: TAE00000Y, ABS: 14-LD234401A-4-PDA, BV: 43180/A1BV
Ingress Protection Rating **IP66 as standard (IP67, IP68 available upon request)**
Deluge Protection ComplianceDTS01:91 option available on request (white ferrule for identification purposes)
Cable Gland MaterialBrass, Electroless Nickel Plated Brass, Aluminium
Seal MaterialCMP SOLO LSF Halogen Free Thermoset Elastomer
Cable TypeLead Sheathed & Single Wire Armour (LC/SWA), Lead Sheathed & Aluminium Wire Armour (LC/
AWA), Lead Sheathed & Wire Braid Armour (LC/SWB), Lead Sheathed & Pliable Wire Armour
(LC/PWA), Lead Sheathed & Steel Tape Armour (LC/STA), Lead Sheathed & Aluminium Strip
Armour (LC/ASA)
Armour ClampingReversible Armour Cone & AnyWay Universal Clamping Ring
Sealing TechniqueCMP Inner Displacement Seal & Unique CMP ‘LRS’ ™ Outer Load Retention Seal
Sealing Area(s)Cable Inner Bedding & Outer Cable Sheath
Optional AccessoriesLocknuts, Earth Tags, Serrated Washers, Entry Thread Seals, Shrouds,Ingress Discs
Optional Installation ToolsSpanners

Product Table

Metric

Cable Gland SizeAvailable Entry Threads “C” (Alternate Metric Thread Lengths Available)Lead Sheath Diameter “A”Overall
Cable
Diameter
“B”		Armour RangeAcross
Flats
“D”		Across
Corners
“D”		Protrusion
Length “F”		Combined Ordering Reference
(*Brass Metric)		ShroudCable
Gland
Weight
(Kgs)
StandardOptionGrooved
Cone (X)		Stepped Cone (W)
MetricThread Length (Metric) “E”NPTThread Length
(NPT) “E”		NPTMinMaxMinMaxMinMaxMinMaxMaxMaxSizeTypeOrdering
Suffix
20S16M2015.0½”19.9¾”3.17.86.113.10.31.00.81.2524.026.472.520S16E2FU1RAPVC040.16
20SM2015.0½”19.9¾”6.111.09.515.90.31.00.81.2524.026.470.020SE2FU1RAPVC040.15
20M2015.0½”19.9¾”6.513.412.520.90.41.00.81.2530.533.673.020E2FU1RAPVC060.21
25SM2515.0¾”20.21″11.119.314.022.00.41.21.251.637.541.389.025SE2FU1RAPVC090.33
25M2515.0¾”20.21″11.119.318.226.20.41.21.251.637.541.389.025E2FU1RAPVC090.33
32M3215.01″25.01 ¼”17.025.523.733.90.41.21.62.046.050.686.032E2FU1RAPVC110.43
40M4015.01 ¼”25.61 ½”22.031.227.940.40.41.61.62.055.060.590.040E2FU1RAPVC150.63
50SM5015.01 ½”26.12″29.537.235.246.70.41.62.02.560.066.091.050SE2FU1RAPVC180.76
50M5015.02″26.92 ½”35.642.640.453.00.61.62.02.570.177.195.050E2FU1RAPVC210.95
63SM6315.02″26.92 ½”40.148.545.659.40.61.62.02.575.082.5102.063SE2FU1RAPVC231.35
63M6315.02 ½”39.93″47.254.254.665.80.61.62.02.580.088.0104.063E2FU1RAPVC251.35
75SM7515.02 ½”39.93″52.860.259.072.00.61.62.02.590.099.0115.075SE2FU1RAPVC282.12
75M7515.03″41.53 ½”59.165.266.778.40.61.62.53.0100.0110.0117.075E2FU1RAPVC302.43
90M9024.03 ½”42.84″66.677.176.290.30.81.63.154.0114.3125.4147.090E2FU1RAPVC324.23
100M10024.03 ½”42.84″76.088.186.1101.40.81.63.154.0123.0135.3140.0100E2FU1RALSF334.47
115M11524.04″44.05″86.094.1101.5110.20.81.63.154.0133.4146.7162.0115E2FU1RALSF346.22
130M13024.05″46.8–97.0110.1110.2123.20.81.63.154.0152.4167.6174.0130E2FU1RALSF358.38
Dimensions displayed in millimeters unless otherwise stated

Imperial

Cable Gland SizeAvailable Entry Threads “C” (Alternate Metric Thread Lengths Available)Lead Sheath Diameter “A”Overall
Cable
Diameter
“B”		Armour RangeAcross
Flats
“D”		Across
Corners
“D”		Protrusion
Length “F”		Combined Ordering Reference
(*Brass Metric)		ShroudCable
Gland
Weight
(Ozs)
StandardOptionGrooved
Cone (X)		Stepped Cone (W)
MetricThread Length (Metric) “E”NPTThread Length
(NPT) “E”		NPTMinMaxMinMaxMinMaxMinMaxMaxMaxSizeTypeOrdering
Suffix
20S16M200.59½”0.78¾”0.120.310.240.520.010.040.030.050.941.042.8520S16E2FU1RAPVC045.64
20SM200.59½”0.78¾”0.240.430.370.630.010.040.030.050.941.042.7620SE2FU1RAPVC045.29
20M200.59½”0.78¾”0.260.530.490.820.020.040.030.051.201.322.8720E2FU1RAPVC067.41
25SM250.59¾”0.801″0.440.760.550.870.020.050.050.061.481.633.5025SE2FU1RAPVC0911.64
25M250.59¾”0.801″0.440.760.721.030.020.050.050.061.481.633.5025E2FU1RAPVC0911.64
32M320.591″0.981 ¼”0.671.000.931.330.020.050.060.081.811.993.3932E2FU1RAPVC1115.17
40M400.591 ¼”1.011 ½”0.871.231.101.590.020.060.060.082.172.383.5440E2FU1RAPVC1522.22
50SM500.591 ½”1.032″1.161.461.391.840.020.060.080.102.362.603.5850SE2FU1RAPVC1826.81
50M500.592″1.062 ½”1.401.681.592.090.020.060.080.102.763.043.7450E2FU1RAPVC2133.51
63SM630.592″1.062 ½”1.581.911.802.340.020.060.080.102.953.254.0263SE2FU1RAPVC2347.62
63M630.592 ½”1.573″1.862.132.152.590.020.060.080.103.153.464.0963E2FU1RAPVC2547.62
75SM750.592 ½”1.573″2.082.372.322.830.020.060.080.103.543.904.5375SE2FU1RAPVC2874.78
75M750.593″1.633 ½”2.332.572.633.090.020.060.100.123.944.334.6175E2FU1RAPVC3085.72
90M900.943 ½”1.694″2.623.043.003.560.030.060.120.164.504.945.7990E2FU1RAPVC32149.21
100M1000.943 ½”1.694″2.993.473.393.990.030.060.120.164.845.335.51100E2FU1RALSF33157.67
115M1150.944″1.735″3.393.704.004.340.030.060.120.165.255.786.38115E2FU1RALSF34219.40
130M1300.945″1.84–3.824.334.344.850.030.060.120.166.006.606.85130E2FU1RALSF35295.60
Dimensions displayed in inches unless otherwise stated