Products > PX2K Explosion Proof Cable Gland
explosive atmosphere univeral armored epoxy gland

PX2K Explosion Proof Cable Gland
explosive atmosphere univeral armored epoxy gland

Globally Approved, Explosive Atmosphere Barrier Cable Gland

• Metal-to-metal armour clamping
• Direct & remote installation
• Compound barrier type flameproof seal
• Controlled outer ‘load retention’ seal
• Unique OSTG prevents overtightening
• Integral protected deluge seal
• -60°C to +85°C
• Class I Zone 1, 21 and Zone 2, 22 Class I Division 1 & 2 ABCD
• Globally marked, IECEx, ATEX, UL & cCSAus
• EMC tested

† Grooved Cone (X) is predominantly used for Wire Braid (e.g. GSWB, TCWB), Steel Tape Armour (STA, DSTA) and Aluminium Strip Armour (ASA) but is also suitable for Single Wire Armour (SWA), Aluminium Wire Armour (AWA) and Pliable Wire Armour (PWA) if the range is outside that of the Stepped Cone (W).

Note: Grooved Cone (X) dimensions shown in the Cable Gland Selection Table below are for a double wire strand of braid armour cables. Tapes can also be doubled over. For cables that have only a single layer of armour such as SWA the clamping range should be used as shown in the table below.

Stepped (W) Cone is suitable for Single Wire Armour (SWA), or Aluminium Wire Armour (AWA) cables.

For under / oversized armour wires

For all types of Armoured cables

Description

PX2K

The PX2K cable gland is a brass compound-filled, flameproof, and gas-tight method of terminating all types of unarmored and braid-armored cables. ATEX-rated for Class I Zone 1, 21, and Zone 2, 22, hazardous areas, this explosion-proof cable gland is ideal for use onshore and offshore or in environments where gas and dust exposure is common. ATEX and IECEx certified hazardous area cable glands.

ATEX Certificates

  • SIRA13ATEX1072X
  • SIRA13ATEX4078X

Approvals

  • LRS: 01/00172 (E3)
  • DNV: TAE00000Y
  • ABS: 14-LD234401A-4-PDA
  • BV: 43180/A1BV

IECEx Certificates

  • IECEx SIR 13.0027X
  • IECEx SIM 14.0008X

UL Certificates

  • E201187
  • E161256C

Code of Protection

  • Class I Div 1, 2, Groups A, B, C, and D
  • Class II Div 1, 2, Groups E, F, and G

This cable gland type features a metal-to-metal armor clamping and compound barrier-type flameproof seal. The gland provides a gas-tight compound barrier around the cable cores and IP66 environmental seal on the outer sheath. It features a reversible armor cone for steel wire armored, steel tape armored, and braided cables. Integrated into the sealing mechanism is an O-ring, which offers enhanced deluge protection. Other features include:

  • Direct And Remote Installation
  • Controlled Outer Load-Retention Seal
  • Unique OSTG Prevents Overtightening
  • Globally Marked, IECEx, ATEX, UL, And cCSAus
  • EMC Tested

 

PX2K explosive atmosphere barrier cable glands are available in brass, electroless nickel-plated brass, stainless steel, and aluminum constructions. EUTEX International’s standard offering is nickel-plated brass.

This cable gland is suitable for operating environments of -60 degrees Celsius, or -76 degrees Fahrenheit, to +85 degrees Celsius, or +185 degrees Fahrenheit. Many applications can benefit from PX2K explosive atmosphere barrier cable glands.

  • Aerospace
  • Defense
  • Chemical
  • Mining
  • Minerals & Metals
  • Commercial Construction
  • Downstream Hydrocarbons
  • Food & Beverage
  • Industrial Energy
  • Onsite Utilities

  • Industrial Machinery
  • Laboratory and R&D
  • Life Sciences
  • Medical
  • Marine
  • Oil & Gas
  • Packaging
  • Power
  • Pulp & Paper
  • Textiles
  • Water & Wastewate

Your Explosion Proof Cable Gland Source

EUTEX International is a top provider of electric cables and accessories for demanding industrial use. An ISO 9001:2015-certified Quality Management System ensures every product we supply is durable, effective, and of the highest quality. With locations located around the world, our team can deliver the electrical products you need on time and within budget.

Feel free to contact us about PX2K cable gland explosive atmosphere products. We’re happy to discuss your needs in greater detail.

Technical

 

Design SpecificationBS 6121:Part 1:1989, IEC 62444, EN 62444
Mechanical Classifications *Impact = Level 8, Retention = Class D
Enclosure ProtectionIK10 to IEC 62262 (20 joules) Brass & Stainless Steel only
Electrical Classifications *Category B (Category A when used with braid, tape or pliable wire armour cables)
ATEX CertificateSIRA13ATEX1072X, SIRA13ATEX4078X
Code of ProtectionII 2G, II 1D, Ex d IIC Gb, Ex e IIC Gb, Ex ta IIIC Da
II 3G Ex nR IIC Gc, IM2 Ex d I Mb, Ex e I Mb
Compliance StandardsEN 60079-0,1,7,15,31
IECEx CertificateIECEx SIR 13.0027X, IECEx SIM 14.0008X
Code of ProtectionEx d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da, Ex d I Mb, Ex e I Mb
Compliance StandardsIEC 60079-0,1,7,15,31
cCSAus Certificate (20s16 – 100)2288626
CSAus Code of Protection***Class I, Div. 1, 2 Groups A, B, C and D; Class II, Div. 1, 2 Groups E, F and G; Class III, Div. 1, 2; Type 4X: Oil Resistant II:
Class I, Zone 1 AEx d IIC Gb, AEx e IIC Gb, Class I, Zone 2 AEx nR IIC Gc, Class I, Zone 20 AEx ta IIIC Da
cCSA Code of Protection***Class I, Div. 1, 2 Groups A, B, C and D; Class II, Div. 1, 2 Groups E, F and G; Class III, Div. 1, 2; Type
4X: Oil Resistant II:
Ex d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da
Compliance StandardsCAN/CSA-C22.2 No 0,18,25,30,94,174, CAN/CSA-E60079-0,1,7,15,31 CAN/CSA-E61241-1-1 Part
1-1, ANSI/UL 514B Ed 5, ANSI/UL 50 Ed 11, ANSI/UL 2225 Ed 4, UL60079
UL Certificate (20s16 – 100)E201187, E161256C
Code of ProtectionClass I Div 1,2, Groups A,B,C,D, Class II Div 1,2, Groups E,F,G
Compliance StandardsUL 2225, CSA C22.2 No 174, UL 514B, CSA C22.2 No 18, CSA C22.2 No 30
UkrSEPROUA.TR.047.C.0644-15
EAC CertificateC-GB.AA87.B.00487
KCC Certificate14-GA4BO-0252X
CCOE / PESO (India) CertificateP333688
NEPSI CertificateGYJ13.1140X, GYJ13.1282X
INMETRO ApprovalTÜV 12.2073X
RETIE Certificate03866
Marine ApprovalsLRS: 01/00172, DNV: TAE00000Y, ABS: 14-LD234401A-4-PDA, BV: 43180/A1BV
Ingress Protection Rating **IP66, IP67 & IP68
Deluge Protection ComplianceDTS01 : 91
Cable Gland MaterialBrass, Electroless Nickel Plated Brass, Stainless Steel, Aluminium
Seal MaterialCMP SOLO LSF Halogen Free Thermoset Elastomer / Epoxy Barrier Compound
Cable TypeSingle Wire Armour (SWA), Aluminium Wire Armour (AWA), Wire Braid Armour (e.g. SWB),
Screened Flexible (EMC) Wire Braid (e.g. CY / SY), Pliable Wire Armour (PWA), Steel Tape
Armour (STA), Strip Armour (e.g. ASA)***
Armour ClampingDetachable Compound Tube / Cone & AnyWay Universal Clamping Ring
Sealing TechniqueUnique CMP ‘LRS’ Outer Seal (Load Retention Seal)
Sealing Area(s)Inner Compound Barrier & Outer Sheath
Optional AccessoriesLocknuts, Earth Tags, Serrated Washers, Entry Thread Seals, Shrouds,Ingress Discs
Optional Installation ToolsSpanners, Armour Former Tool

Product Table

Metric

Cable Gland SizeAvailable Entry Threads “C” (Alternate Metric Thread Lengths Available)Number of CoresDiameter Over Conductors
“A”
Cable Bedding Diameter “G”Overall
Cable
Diameter
“B”
Armour RangeAcross
Flats
“D”
Across
Corners
“D”
Protrusion
Length “F”
Combined Ordering Reference
(*Brass Metric)
ShroudCable
Gland
Weight
(Kgs)
StandardOptionGrooved
Cone (X)
Stepped Cone (W)
MetricThread Length (Metric) “E”NPTThread Length
(NPT) “E”
NPTMaxMinMaxMinMaxMinMaxMaxMaxSizeTypeOrdering
Suffix
20S16M2015.0½”19.9¾”1111.711.76.113.10.31.00.81.2530.533.662.020S16PX2K1RAPVC060.24
20SM2015.0½”19.9¾”1111.711.79.515.90.31.00.81.2530.533.662.020SPX2K1RAPVC060.23
20M2015.0½”19.9¾”1112.612.912.520.90.41.00.81.2530.533.663.020PX2K1RAPVC060.24
25SM2515.0¾”20.21″2117.517.914.022.00.41.21.251.637.541.369.525SPX2K1RAPVC090.37
25M2515.0¾”20.21″2117.517.918.226.20.41.21.251.637.541.369.525PX2K1RAPVC090.37
32M3215.01″25.01 ¼”3823.623.923.733.90.41.21.62.046.050.675.032PX2K1RAPVC110.57
40M4015.01 ¼”25.61 ½”5930.030.327.940.40.41.61.62.055.060.575.040PX2K1RAPVC150.80
50SM5015.01 ½”26.12″8936.636.935.246.70.41.62.02.560.066.077.050SPX2K1RAPVC180.90
50M5015.02″26.92 ½”8941.041.340.453.00.61.62.02.570.077.077.050PX2K1RAPVC211.19
63SM6315.02″26.92 ½”11547.948.445.659.40.61.62.02.575.082.579.763SPX2K1RAPVC231.39
63M6315.02 ½”39.93″11553.754.054.665.80.61.62.02.580.088.080.363PX2K1RAPVC251.41
75SM7515.02 ½”39.93″14059.960.259.072.00.61.62.02.590.099.086.875SPX2K1RAPVC282.09
75M7515.03″41.53 ½”14064.264.266.778.40.61.62.53.0100.0110.088.375PX2K1RAPVC302.54
90M9024.03 ½”42.84″20075.375.676.290.30.81.63.154.0115.0126.5102.190PX2K1RAPVC323.71
100M10024.03 ½”42.84″20085.685.986.1101.40.81.63.154.0127.0139.7114.0100PX2K1RALSF334.31
Dimensions displayed in millimeters unless otherwise stated

Imperial

Cable Gland SizeAvailable Entry Threads “C” (Alternate Metric Thread Lengths Available)Number of CoresDiameter Over Conductors
“A”
Cable Bedding Diameter “G”Overall
Cable
Diameter
“B”
Armour RangeAcross
Flats
“D”
Across
Corners
“D”
Protrusion
Length “F”
Combined Ordering Reference
(*Brass Metric)
ShroudCable
Gland
Weight
(Ozs)
StandardOptionGrooved
Cone (X)
Stepped Cone (W)
MetricThread Length (Metric) “E”NPTThread Length
(NPT) “E”
NPTMaxMinMaxMinMaxMinMaxMaxMaxSizeTypeOrdering
Suffix
20S16M200.59½”0.78¾”110.460.460.240.520.010.040.030.051.201.322.4420S16PX2K1RAPVC068.47
20SM200.59½”0.78¾”110.460.460.370.630.010.040.030.051.201.322.4420SPX2K1RAPVC068.11
20M200.59½”0.78¾”110.500.510.490.820.020.040.030.051.201.322.4820PX2K1RAPVC068.47
25SM250.59¾”0.801″210.690.700.550.870.020.050.050.061.481.632.7425SPX2K1RAPVC0913.05
25M250.59¾”0.801″210.690.700.721.030.020.050.050.061.481.632.7425PX2K1RAPVC0913.05
32M320.591″0.981 ¼”380.930.940.931.330.020.050.060.081.811.992.9532PX2K1RAPVC1120.11
40M400.591 ¼”1.011 ½”591.181.191.101.590.020.060.060.082.172.382.9540PX2K1RAPVC1528.22
50SM500.591 ½”1.032″891.441.451.391.840.020.060.080.102.362.603.0350SPX2K1RAPVC1831.75
50M500.592″1.062 ½”891.611.631.592.090.020.060.080.102.763.033.0350PX2K1RAPVC2141.98
63SM630.592″1.062 ½”1151.891.911.802.340.020.060.080.102.953.253.1463SPX2K1RAPVC2349.03
63M630.592 ½”1.573″1152.112.132.152.590.020.060.080.103.153.463.1663PX2K1RAPVC2549.74
75SM750.592 ½”1.573″1402.362.372.322.830.020.060.080.103.543.903.4275SPX2K1RAPVC2873.72
75M750.593″1.633 ½”1402.532.532.633.090.020.060.100.123.944.333.4875PX2K1RAPVC3089.60
90M900.943 ½”1.694″2002.962.983.003.560.030.060.120.164.534.984.0290PX2K1RAPVC32130.87
100M1000.943 ½”1.694″2003.373.383.393.990.030.060.120.165.005.504.49100PX2K1RALSF33152.03
Dimensions displayed in inches unless otherwise stated

Download Spec Sheet

Download

PX2K

The PX2K cable gland is a brass compound-filled, flameproof, and gas-tight method of terminating all types of unarmored and braid-armored cables. ATEX-rated for Class I Zone 1, 21, and Zone 2, 22, hazardous areas, this explosion-proof cable gland is ideal for use onshore and offshore or in environments where gas and dust exposure is common. ATEX and IECEx certified hazardous area cable glands.

ATEX Certificates

  • SIRA13ATEX1072X
  • SIRA13ATEX4078X

Approvals

  • LRS: 01/00172 (E3)
  • DNV: TAE00000Y
  • ABS: 14-LD234401A-4-PDA
  • BV: 43180/A1BV

IECEx Certificates

  • IECEx SIR 13.0027X
  • IECEx SIM 14.0008X

UL Certificates

  • E201187
  • E161256C

Code of Protection

  • Class I Div 1, 2, Groups A, B, C, and D
  • Class II Div 1, 2, Groups E, F, and G

This cable gland type features a metal-to-metal armor clamping and compound barrier-type flameproof seal. The gland provides a gas-tight compound barrier around the cable cores and IP66 environmental seal on the outer sheath. It features a reversible armor cone for steel wire armored, steel tape armored, and braided cables. Integrated into the sealing mechanism is an O-ring, which offers enhanced deluge protection. Other features include:

  • Direct And Remote Installation
  • Controlled Outer Load-Retention Seal
  • Unique OSTG Prevents Overtightening
  • Globally Marked, IECEx, ATEX, UL, And cCSAus
  • EMC Tested

 

PX2K explosive atmosphere barrier cable glands are available in brass, electroless nickel-plated brass, stainless steel, and aluminum constructions. EUTEX International’s standard offering is nickel-plated brass.

This cable gland is suitable for operating environments of -60 degrees Celsius, or -76 degrees Fahrenheit, to +85 degrees Celsius, or +185 degrees Fahrenheit. Many applications can benefit from PX2K explosive atmosphere barrier cable glands.

  • Aerospace
  • Defense
  • Chemical
  • Mining
  • Minerals & Metals
  • Commercial Construction
  • Downstream Hydrocarbons
  • Food & Beverage
  • Industrial Energy
  • Onsite Utilities

  • Industrial Machinery
  • Laboratory and R&D
  • Life Sciences
  • Medical
  • Marine
  • Oil & Gas
  • Packaging
  • Power
  • Pulp & Paper
  • Textiles
  • Water & Wastewate

Your Explosion Proof Cable Gland Source

EUTEX International is a top provider of electric cables and accessories for demanding industrial use. An ISO 9001:2015-certified Quality Management System ensures every product we supply is durable, effective, and of the highest quality. With locations located around the world, our team can deliver the electrical products you need on time and within budget.

Feel free to contact us about PX2K cable gland explosive atmosphere products. We’re happy to discuss your needs in greater detail.

Technical

 

Design SpecificationBS 6121:Part 1:1989, IEC 62444, EN 62444
Mechanical Classifications *Impact = Level 8, Retention = Class D
Enclosure ProtectionIK10 to IEC 62262 (20 joules) Brass & Stainless Steel only
Electrical Classifications *Category B (Category A when used with braid, tape or pliable wire armour cables)
ATEX CertificateSIRA13ATEX1072X, SIRA13ATEX4078X
Code of ProtectionII 2G, II 1D, Ex d IIC Gb, Ex e IIC Gb, Ex ta IIIC Da
II 3G Ex nR IIC Gc, IM2 Ex d I Mb, Ex e I Mb
Compliance StandardsEN 60079-0,1,7,15,31
IECEx CertificateIECEx SIR 13.0027X, IECEx SIM 14.0008X
Code of ProtectionEx d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da, Ex d I Mb, Ex e I Mb
Compliance StandardsIEC 60079-0,1,7,15,31
cCSAus Certificate (20s16 – 100)2288626
CSAus Code of Protection***Class I, Div. 1, 2 Groups A, B, C and D; Class II, Div. 1, 2 Groups E, F and G; Class III, Div. 1, 2; Type 4X: Oil Resistant II:
Class I, Zone 1 AEx d IIC Gb, AEx e IIC Gb, Class I, Zone 2 AEx nR IIC Gc, Class I, Zone 20 AEx ta IIIC Da
cCSA Code of Protection***Class I, Div. 1, 2 Groups A, B, C and D; Class II, Div. 1, 2 Groups E, F and G; Class III, Div. 1, 2; Type
4X: Oil Resistant II:
Ex d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da
Compliance StandardsCAN/CSA-C22.2 No 0,18,25,30,94,174, CAN/CSA-E60079-0,1,7,15,31 CAN/CSA-E61241-1-1 Part
1-1, ANSI/UL 514B Ed 5, ANSI/UL 50 Ed 11, ANSI/UL 2225 Ed 4, UL60079
UL Certificate (20s16 – 100)E201187, E161256C
Code of ProtectionClass I Div 1,2, Groups A,B,C,D, Class II Div 1,2, Groups E,F,G
Compliance StandardsUL 2225, CSA C22.2 No 174, UL 514B, CSA C22.2 No 18, CSA C22.2 No 30
UkrSEPROUA.TR.047.C.0644-15
EAC CertificateC-GB.AA87.B.00487
KCC Certificate14-GA4BO-0252X
CCOE / PESO (India) CertificateP333688
NEPSI CertificateGYJ13.1140X, GYJ13.1282X
INMETRO ApprovalTÜV 12.2073X
RETIE Certificate03866
Marine ApprovalsLRS: 01/00172, DNV: TAE00000Y, ABS: 14-LD234401A-4-PDA, BV: 43180/A1BV
Ingress Protection Rating **IP66, IP67 & IP68
Deluge Protection ComplianceDTS01 : 91
Cable Gland MaterialBrass, Electroless Nickel Plated Brass, Stainless Steel, Aluminium
Seal MaterialCMP SOLO LSF Halogen Free Thermoset Elastomer / Epoxy Barrier Compound
Cable TypeSingle Wire Armour (SWA), Aluminium Wire Armour (AWA), Wire Braid Armour (e.g. SWB),
Screened Flexible (EMC) Wire Braid (e.g. CY / SY), Pliable Wire Armour (PWA), Steel Tape
Armour (STA), Strip Armour (e.g. ASA)***
Armour ClampingDetachable Compound Tube / Cone & AnyWay Universal Clamping Ring
Sealing TechniqueUnique CMP ‘LRS’ Outer Seal (Load Retention Seal)
Sealing Area(s)Inner Compound Barrier & Outer Sheath
Optional AccessoriesLocknuts, Earth Tags, Serrated Washers, Entry Thread Seals, Shrouds,Ingress Discs
Optional Installation ToolsSpanners, Armour Former Tool

Product Table

Metric

Cable Gland SizeAvailable Entry Threads “C” (Alternate Metric Thread Lengths Available)Number of CoresDiameter Over Conductors
“A”
Cable Bedding Diameter “G”Overall
Cable
Diameter
“B”
Armour RangeAcross
Flats
“D”
Across
Corners
“D”
Protrusion
Length “F”
Combined Ordering Reference
(*Brass Metric)
ShroudCable
Gland
Weight
(Kgs)
StandardOptionGrooved
Cone (X)
Stepped Cone (W)
MetricThread Length (Metric) “E”NPTThread Length
(NPT) “E”
NPTMaxMinMaxMinMaxMinMaxMaxMaxSizeTypeOrdering
Suffix
20S16M2015.0½”19.9¾”1111.711.76.113.10.31.00.81.2530.533.662.020S16PX2K1RAPVC060.24
20SM2015.0½”19.9¾”1111.711.79.515.90.31.00.81.2530.533.662.020SPX2K1RAPVC060.23
20M2015.0½”19.9¾”1112.612.912.520.90.41.00.81.2530.533.663.020PX2K1RAPVC060.24
25SM2515.0¾”20.21″2117.517.914.022.00.41.21.251.637.541.369.525SPX2K1RAPVC090.37
25M2515.0¾”20.21″2117.517.918.226.20.41.21.251.637.541.369.525PX2K1RAPVC090.37
32M3215.01″25.01 ¼”3823.623.923.733.90.41.21.62.046.050.675.032PX2K1RAPVC110.57
40M4015.01 ¼”25.61 ½”5930.030.327.940.40.41.61.62.055.060.575.040PX2K1RAPVC150.80
50SM5015.01 ½”26.12″8936.636.935.246.70.41.62.02.560.066.077.050SPX2K1RAPVC180.90
50M5015.02″26.92 ½”8941.041.340.453.00.61.62.02.570.077.077.050PX2K1RAPVC211.19
63SM6315.02″26.92 ½”11547.948.445.659.40.61.62.02.575.082.579.763SPX2K1RAPVC231.39
63M6315.02 ½”39.93″11553.754.054.665.80.61.62.02.580.088.080.363PX2K1RAPVC251.41
75SM7515.02 ½”39.93″14059.960.259.072.00.61.62.02.590.099.086.875SPX2K1RAPVC282.09
75M7515.03″41.53 ½”14064.264.266.778.40.61.62.53.0100.0110.088.375PX2K1RAPVC302.54
90M9024.03 ½”42.84″20075.375.676.290.30.81.63.154.0115.0126.5102.190PX2K1RAPVC323.71
100M10024.03 ½”42.84″20085.685.986.1101.40.81.63.154.0127.0139.7114.0100PX2K1RALSF334.31
Dimensions displayed in millimeters unless otherwise stated

Imperial

Cable Gland SizeAvailable Entry Threads “C” (Alternate Metric Thread Lengths Available)Number of CoresDiameter Over Conductors
“A”
Cable Bedding Diameter “G”Overall
Cable
Diameter
“B”
Armour RangeAcross
Flats
“D”
Across
Corners
“D”
Protrusion
Length “F”
Combined Ordering Reference
(*Brass Metric)
ShroudCable
Gland
Weight
(Ozs)
StandardOptionGrooved
Cone (X)
Stepped Cone (W)
MetricThread Length (Metric) “E”NPTThread Length
(NPT) “E”
NPTMaxMinMaxMinMaxMinMaxMaxMaxSizeTypeOrdering
Suffix
20S16M200.59½”0.78¾”110.460.460.240.520.010.040.030.051.201.322.4420S16PX2K1RAPVC068.47
20SM200.59½”0.78¾”110.460.460.370.630.010.040.030.051.201.322.4420SPX2K1RAPVC068.11
20M200.59½”0.78¾”110.500.510.490.820.020.040.030.051.201.322.4820PX2K1RAPVC068.47
25SM250.59¾”0.801″210.690.700.550.870.020.050.050.061.481.632.7425SPX2K1RAPVC0913.05
25M250.59¾”0.801″210.690.700.721.030.020.050.050.061.481.632.7425PX2K1RAPVC0913.05
32M320.591″0.981 ¼”380.930.940.931.330.020.050.060.081.811.992.9532PX2K1RAPVC1120.11
40M400.591 ¼”1.011 ½”591.181.191.101.590.020.060.060.082.172.382.9540PX2K1RAPVC1528.22
50SM500.591 ½”1.032″891.441.451.391.840.020.060.080.102.362.603.0350SPX2K1RAPVC1831.75
50M500.592″1.062 ½”891.611.631.592.090.020.060.080.102.763.033.0350PX2K1RAPVC2141.98
63SM630.592″1.062 ½”1151.891.911.802.340.020.060.080.102.953.253.1463SPX2K1RAPVC2349.03
63M630.592 ½”1.573″1152.112.132.152.590.020.060.080.103.153.463.1663PX2K1RAPVC2549.74
75SM750.592 ½”1.573″1402.362.372.322.830.020.060.080.103.543.903.4275SPX2K1RAPVC2873.72
75M750.593″1.633 ½”1402.532.532.633.090.020.060.100.123.944.333.4875PX2K1RAPVC3089.60
90M900.943 ½”1.694″2002.962.983.003.560.030.060.120.164.534.984.0290PX2K1RAPVC32130.87
100M1000.943 ½”1.694″2003.373.383.393.990.030.060.120.165.005.504.49100PX2K1RALSF33152.03
Dimensions displayed in inches unless otherwise stated